P/N: CLW0211
Bigwater 760 Plus
Design Gallery Specification Video Reviews Support

 
Bigwater 760 Plus
 

Features

 

Dual 5.25 Drive Bay design: liquid cooling system in-a-box to save the space in the chassis and simplifies installation

  1. Front- VRTM control knob, adjusts fan speed conveniently
  2. Mesh design front bezel enhances ventilation
  3. Easy to install and refill

- Front-water level alarm signal, master the timing of refilling

- 12cm Motorsports Radiator:
1. Dimple Tube Technology swirls the coolant within the radiator to increase thermal transfer.
2. An all-aluminum radiator featuring expanded outer fins and tube style for maximum performance.

- Pure Copper Base Waterblock with high efficiency channel design

- Ultra-low noise fan: silent variable fan with blue LED (1600 ~ 2400rpm).

- High-performance Liquid Pump:   
1. Silent and powerful P500 (500L/hr) pump provide superb reliability.
2. The ceramic bearings significantly extend the life-expectancy of the pump.

- Universal Socket Compatibility & Accessory Package
1. All-in-one back-plate design, support all Intel and AMD platform
2. Universal socket support :
Intel: LGA1366, LGA1156, LGA1155, LGA775
AMD: FM2, FM1, AM3, AM2+, AM2

- 3/8” UV sensitive Water Tube: Special material to prevent wear & tare from being clogged up or over bending


Detailed Features

P500 Pump
Flow rate : 500L/hr, can easily handle extra water blocks for GPU, memory, HDD or chipsets.
Refill Reservoir
Transparent reservoir for easy refilling
VR Control Knob
The control knob allows user to adjust fan speed conveniently
Motorsports Radiator
Dimple Tube Technology with louvered fin radiator greatly increases the surface area for added cooling capability
Nickel-Plated Copper Base
Mirror base provides good contact with CPU surface
Blue LED VR fan
Adjustable 120x120x25mm blue LED fan, fan speed from 1600~2400RPM
Water Level Alarm Signal
Liquid level sensor detects the coolant level in real-time


Performance


Installation

For ease of use, Thermaltake recommends placing the liquid cooling module(A) into the following 5.25" bay drive position:

Full Tower:3rd or 4th 5.25" bay drive from the top.
Mid Tower:2nd or 3rd 5.25" bay drive from the top.

Step 1 Step 2
Remove the drive bay cover from the selection position and the screws on the back of the chassis, open the side panel.(The following diagrams are the Thermaltake Level 10 GT case)

Insert the liquid cooling module into 5.25” drive bay.
Make sure the screw hole lines up as diagram. Push the latch forward until it locks.

If your case doesn’t have the free clip, please secure the liquid cooling module by 5mm screws.
Step 3 Step 4
Insert the hose clip through the water tube connecting the liquid cooling module. Insert the hose clip through the water tube connecting the liquid cooling module.
Step 5 Step 6
Repeat the installation steps for the other side shown on photo. Connect the 3pin wire to the motherboard’s CPU fan connector (3pin or 4pin)
Step 7 Step 8
Open the cover of liquid tank. Fill the tank up with coolant.
Step 9 Step 10
Turn on the PC power switch, liquid level will decrease when you power on the system, please keep filling coolant until the tank is filled up.

Please make sure liquid is flowing continuously and smoothly within the tube.
After tank is filled up, you can close the cover of liquid tank, and adjust the fan speed, then turn off the PC power switch if everything is done.

Your installation is completed, congratulation!
Note
  1. If bubbles are forming within the tubing , you may tap the tube gently to remove them until all are gone.
  2. After installation is completed, please ensure there are no bent tubings.