Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC Water 3.0 Performer C + LNC
Water 3.0 Performer C + LNC

Water 3.0 Performer C + LNC

Out of stock
P/N
CLW0222-B
USD$59.99

A flexible all-in-one liquid cooler that provides easy and safe installation.
*China Only

Thermaltake Water 3.0 Performer C with Low noise Cable (LNC)

When choosing a high-efficiency liquid cooler to control roaring CPU temps, enthusiasts crave an easy, clean, and low-maintenance setup . The new Thermaltake All-In-One LCS Water 3.0 Series is designed to exceed user expectations. One simple upgrade allows users to enjoy better cooling performance and greater CPU protection. In addition, low noise cable is optimized for lower speed and silent operation
*China Only

High Performance Waterblock

Full copper base plate maximizes heat conductivity while improving the case''s airflow.

High Efficiency Radiator

Specially designed 120mm large surface radiator, supported by a 120mm fan for additional heat dissipation.

Powerful Cooling Fan

An automatically adjustable 120mm PWM Fan maximizes the cooling performance and tranquility with speed up to 2000RPM, minimizing any overheating possibility.The LNC (Low-Noise Cable) can reduce the noise level by 47% from 39.9dBA to 21dBA.

*LNC (Low Noise Cable)

High Reliability Pump

The high quality, reliable pump enables maximum water circulation and keeps the copper plate continuously cool.

Universal Socket Compatibility

Water 3.0 Performer C supports most Intel and AMD sockets, including mountings for Intel Socket LGA 2011/1366/1156/1155/1150. It’s universally compatible with a wide range of AMD platforms.

Cautions

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks

  • To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
  • Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
  • Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup

  • It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
  • Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
  • DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
  • Fill the reservoir to the top as it will prevent air from going into the pump
  • If necessary tilt the system slightly from side to side to bleed the air out of the loop.
  • Place some paper towels under fittings and joining points to test for leaks.
  • Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
  • Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
  • Coolant might fade over time.
More Information
P/N CLW0222-B
Weight 750 g
PUMP Motor Speed : 2900 ±150 R.P.M
Rated Voltage : 12 V
Rated Current : 175 mA
WATER BLOCK Material : Copper
Fan Dimension : 120 x 120 x 25 mm
Speed : 1200~2000 RPM
Noise Level : 27.36 dB-A(MAX)
Rated Voltage : 12 V
Rated Current : 0.5 A
Max. Air Flow : 81.32 CFM
Connector : 4 pin
Tube Length : 300mm
Material : Rubber
Radiator Dimension : 151 x 120 x 27 mm
Material : Aluminum
COMPATIBILITY Intel LGA 2066/2011-3/2011/1366/1156/1200/1156/1155/1151/1150/775
AMD AM4/FM2/FM1/AM3+/AM3/AM2+/AM2